<p>Stromwächter DG 3300<br />Current Measuring Contactor DG 3300</p>

Current Measuring Contactor DG 3300

Monitoring of 1/5 A AC/DC Current

With the Current Measuring Contactor DG 3300 DRAGO is extending its offer on high-functional and high-reliable components of the interface technique.

Easy selection of operating mode
MIN / MAX alarm and N.O. / N.C. contact can be easily set by using DIP switch
Relay with high power handling
SPDT relay with 6 A current switch capability
True 4-port separation
Protection against erroneous measurements due to parasitic voltages or ground loops
Switch state indicated by LED
Easy to adjust the set point and hysteresis
Protective Separation acc. to EN 50178
Protects service personnel and downstream devices against impermissibly high voltage
High reliability and long-term stability
New APT technology, no maintenance costs
Unlimited use with 24 V AC/DC power supply
Universally applicable for all measurement and industrial applications
5 Years Warranty

The Current Measuring Contactor DG 3300 is used to monitor limit values of 0...1/5 A AC/DC current circuits. High reliability and Protective Separation are essential characteristics that contribute to fault-free equipment operation.

Two switch channels can be separately configured. The switch point and the switch hysteresis can each be adjusted by means of their own 12-turn potentiometer located on the unit’s front panel. The switch state is indicated by a yellow LED.

The direction of effect and the mode of operation can be switched by means of DIP switch settings. Both switch outputs can be set up as either MIN or MAX alarms. The relay contacts switch high power loads either as N.O. or N.C. contacts.

Protective Separation and the 24 V AC/DC power supply make the DG 3300 universally applicable for all measurement and industrial applications, as well as for building automation.

Technical Data

Input

Input signal	DC: 0 ... 1 A, ± 1 A, 0 ... 5 A, ± 5 A AC: 0 ... 1 A, 0 ... 5 A sinusoidal alternating currents, f = 10 ... 500 Hz
Input resistance	< 10 mOhm
Overload	2 x IN continuous, surge current: 100 A for 1 s
Set point range	0 ... 100 % of input range with 12-turn potentiometer , MIN/MAX-Alarm switchable
Hystersis	0 ... 60 % of final value with 12-turn potentiometer

Output

Contact type	2 SPDT relays, mode of operation switchable
Switching capability	250 V AC/DC, max. 6 A, max. 1500 VA
Switch state indicator	Yellow LED
Response time	DC: approx. 20 ms, AC: 500 ms

General Data

Set point error	0,2 % of final value
Temperature coefficient 1)	150 ppm/K of final value
Test voltage	4 kV, 50 Hz, input against power supply against both relays 2.5 kV, 50 Hz, relay I against relay II
Working voltage 2) (Basic Insulation)	Up to 600 V AC/DC for overvoltage category III and pollution degree 2 acc. to EN 50178 between input, power supply and relay outputs. Up to 300 V AC/DC between both relay outputs.
Protection against electrical shock 2)	Protective separation according to EN 50178 by reinforced insulation up to 300 V AC/DC for overvoltage category II and pollution degree 2 between input, power supply and relay outputs.
Power supply	24 V AC/DC, ± 15 %	AC: 48 ... 62 Hz, approx. 2 VA DC: approx. 1 W
Ambient temperature	Operation Transport and storage	–20 °C to +60 °C –35 °C to +85 °C
EMC 3)	EN 61326 -1
Construction	22.5 mm housing, protection class: IP 20
Weight	Approx. 100 g

Average TC in specified operating temperature range.
As far as relevant the standards and rules mentioned above are considered by development and production of our devices. In addition relevant assembly rules are to be considered by installation of our devices in other equipments. For applications with high working voltages, take measures to prevent accidental contact and make sure that there is sufficient distance or insulation between adjacent situated devices.
Minor deviations possible during interference.